#10-32 Tee Nuts Pack of Ten – 4410-01118-00
$3.69Product Description
T-Nut 10-32 – 3/4″‘ base – 7/16″ barrel. Sold in a pack of Ten
3-prong t-nut 10-32 thread, barrel height 7/16″ with 3/4″ diameter base.
These nuts are used on virtually every pinball machine ever produced.
Reference : # 4410-01118-00
Bin: P07.4
#10-32 x 1/2″ Pan Head Screw Thread Cutting. Pack of Ten 237-6033-00
$9.00Product Description
#10-32 x 1/2″ #10-32 x 1/2″ Pan Head Screw Thread Cutting. Pack of Ten #237-6033-00
#10-32 x 1/2″ Pan Screw With Locking Washer. Pack of Ten #4010-01006-08.
$9.00Product Description
#10-32 x 1/2″ Pan Screw With Locking Washer
Commonly used on most all pinball machines.
Comes with locking washer.
Williams/Bally reference #4010-01006-08.
Sold in a pack of 10
Bin: P07.4
#10-32 x 3/8″ Serrated slotted Hex Washer Thread Forming Pack of Ten #237-5985-00
$8.00Product Description
wage head screw used to fasten coil stops to Stern flipper assembly bases.Possibly used elsewhere in use as well.
#10-32 x 3/8″ Serrated slotted Hex Washer
Sold in a pack of 10
Stern #237-5985-00.
Bin: P07.4
#4-40 x Nyloc Nuts Pack of Ten 4404-01119-00
$3.00Product Description
#4-40 nylon lock nut (also referred to as a nylock).
Small lock nut used in some pinball machines.
Stern reference #240-5303-00.
Williams/Bally reference #4404-01119-00.
Bin: P07.4
#6-32 Nylon Insert Lock Nut pack of ten 240-5102-00_066-32
$2.60Product Description
Sold in a Pack of Ten
Part no :240-5102-00_066-32 Nylon Lock Nuts (Nylocks).
Used in countless playfield applications on virtually every pinball machine ever built.
Bin: P07.4
#6-32 x 5/8″ Pan Screw. Pack of Ten – 4006-01003-10
$3.50Product Description
Part no : 4006-01004-10
Used in countless playfield applications on virtually every pinball machine ever built.
Sold in a Pack of Ten
Bin: P07.4
#8-32 x 1/4″ Pan Screw Black Oxide Finish. Pack of Ten 4008-01003-04b
$4.50Product Description
Part no :4008-01003-04b pan screw Black oxide finish
Used in countless playfield applications on virtually every pinball machine ever built.
Sold in a Pack of Ten
Bin: P07.4
6-32 x 3/8″ with built in washer Sold in a Pack of Ten. 4006-01027-06.
$2.60Product Description
6-32 x 3/8″ with built in washer pack of ten
Officially known as MS 6-32 x 3/8 P-RWH.
Used all over the playfield on most Williams/Bally games.
Williams/Bally reference #4006-01027-06.
Bin: P07.4
6-32 x 5/8″ Pan Screw with Locking Washer #4006-01017-04.
$4.60Product Description
Pan head screws 8 – 32 x 5/8 ms sems can also be used used on Williams Bally Data East / Sega/ Stern pinball machines comes in a pack of Ten
Reference No #4006-01017-04
8-32 Nylon Nuts Pack of Ten 4406-01119-00
$3.30Product Description
#8-32 nylon lock nut (also referred to as a nylock).
Used in countless playfield applications on virtually every pinball machine ever built.
Sold in a pack of ten
Reference:
240-5005-00 zinc plated 6-32 stopnut
4406-01119-00 zinc plated 6-32 stopnut
Bin: P07.4
BALL SHOOTER – FLATWASHER – 4700-00051-00. – Sold As A Individual Item
$0.20Product Description
Flatwasher Washer .390 x .625 x .059 Shooter rod. Part No 4700-00051-00
Williams/Bally reference #4700-00051-00.
Data East/Sega/Stern reference #242-5014-00.
Jersey Jack Pinball reference #95-002564-58-16.
Bin: P07.8
BALLY – WILLIAMS 5VOLT RESET PCB – #WPC-PDA12697R
$52.95Product Description
Reset Fix Board WPC Power Driver
Plug in Reset Fix Board with voltage indicator LEDs for the Bally / Williams WPC pinball System part # A-12697-1, A-12697-3, A-12697-4 power / driver boards.
The Reset Fix Board prevents and diagnoses intermittent game shutdown problems on Bally/Williams WPC (Williams Pinball Controller) System pinball machines. Easy plug and play, 5 minute, no tool installation.
How it works: When a game suddenly shuts off, goes dark and reboots itself after a few second delay, an MPU board reset has occurred. Unwanted resets occur on WPC pinball machine MPU boards because the Power Driver Board’s (PDB) 5 volt power supply is marginally designed for the many circuits it drives.
The Reset Fix Board creates a unique 5 volt power source for the WPC System MPU board and adds 5v and 12v circuit monitor LEDs to your Power Driver Board.
WPC series MPU boards have a watchdog circuit that shuts down the board if the 5 volt power supply drops below a cutoff voltage (~ 4.7 volts). This happens more frequently as game circuitry ages, and the machine unexpectedly turns off and ends any active games. Ironically, the watchdog circuit shut down often reduces the 5 volt load, the voltage quickly recovers, and the machine restarts normally.
Unfortunately, the problem persists and re-energizing the MPU board quickly loads down the 5 volt power supply and the watchdog again resets the MPU. This creates an endless on/off reset cycle about every two seconds. Even if the machine doesn’t enter this rapid “reset loop”, there will be more intermittent resets – often within minutes, hours or longer intervals.
The Reset Fix Board eliminates watchdog circuit resets by removing the MPU load from the PDB 5 volt circuit and re-routing it to the more powerful 12 volt circuit. The Reset Fix Board omits connector pins from the wire-side connector and eliminates the PDB 5 volt connection to the MPU board. Instead, a new switched regulator circuit generates a stable 5 volt power supply used exclusively by the MPU board. This satisfies the watchdog circuit and the MPU board will not unnecessarily reset.
Other circuits in your pinball machine still use the original 5 volt power supply, so always replace failed capacitors, burnt connector pins, and bad rectifier diodes to keep this circuit healthy. These repairs require intermediate technical proficiency in circuit board rework
How to read the LED indicators:
- Green LED lit: Both 5v and 12v power supplies are stable
- Green LED flashing:5v supply exceeded 5.6v
- Red LED lit : PDB 5v power supply dipped below the voltage that would have triggered a reset after startup.
- Red LED Flashing: 5v supply very low and needs maintenance
- Blue LED lit: 12v supply is weak – PDB 12v regulated supply dropped below 9 volts after startup.
- Red and Blue LEDs lit: both 5v and 12v power supplies on your PDB have triggered alerts.
-
Kit includes:
- Reset Fix Board with LED indicators
- Installation and operation instructions
Reference:
- WPC-PDA12697X rebuild kit
- A-12697-1 WPC power driver pcb assembly
- A-12697-3 WPC power driver pcb assembly
- A-12697-4 WPC power driver pcb assembly
Part no #WPC-PDA12697R
Bin No:P03.6
BALLY – WILLIAMS 7 Switch Opto PCB Assembly with Mounting Bracket
$120.99Product Description
7 Switch Opto PCB Assembly – With Mounting Bracket
Williams/Bally reference A-15595
Bin No:P03.6
BALLY – WILLIAMS COIL RETAINING BRACKET – 01-1747
$4.90Product Description
Bracket – Coil Retainer
Coil retainer bracket is used on many Williams / Bally late model pinball machines.
Reference No:
01-1747
1A-1747
Bin: P07.1
BALLY – WILLIAMS POP BUMPER SWITCH MOUNTING BRACKET – 01-1168
$4.79Product Description
Bracket – Pop Bumper Switch Mounting Bracket
Reference No:
01-1168
Bin: P07.1